Share:


A study on analytical T-stub prying models for RHS joints in tension

    Andrej Mudrov Affiliation
    ; Gintas Šaučiuvėnas Affiliation
    ; Antanas Šapalas Affiliation

Abstract

The article investigates analytical models for calculation of tension capacity of axially-loaded RHS end-plate joints bolted along two and four sides of the tube in order to investigate the phenomena of prying. Design of such joints is impeded by lack of rules in EN 1993-1-8 and it raises the question whether the Eurocode 3 equivalent T-stub in the tension component should contain integrated assumptions from the AISC/CIDECT/CISC design guides. This paper considers the effect of the bolt hole on the length of the plastic hinge and compares different T-stub models with various assumptions. The behaviour and collapse mechanism of joints with non-preloaded and preloaded bolts was tested during an experiment. The statistical analysis of the test results of 47 joints found in the literature in conjunction with 7 tests determined that it was preferable to use a common approach for connections bolted along two and four sides. Additionally, a limitation of a minimum flange thickness is specified. The performed research has disclosed the benefits and shortcomings of the T-stub models and justified recommendations for their improvement.

Keyword : T-stub, flange, bolt, connections, joints, hollow sections

How to Cite
Mudrov, A., Šaučiuvėnas, G., & Šapalas, A. (2019). A study on analytical T-stub prying models for RHS joints in tension. Engineering Structures and Technologies, 11(1), 1-10. https://doi.org/10.3846/est.2019.8854
Published in Issue
Mar 25, 2019
Abstract Views
1606
PDF Downloads
769
Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

References

Agerskov, H. (1974). Behaviour of connections using prestressed high strength bolts loaded in tension (Report No. R55). Department of Structural Engineering, Technical University of Denmark, Lyngby, Denmark.

Bruno, L. (1984). Bolted end-plate splices in HSS tension members (Masters thesis). University of Toronto, Toronto, Ontario, Canada.

Douty, R. T., & McGuire, W. (1965). High strength moment connections. Journal of Structural Engineering, 91(4), 101-128.

European Committee for Standardization. (2005). Eurocode 3: Design of steel structures. Part 1–8: Design of joints (EN 1993-1-8:2005). Brussels, Belgium.

Jaspart, J. P., & Maquoi, R. (1991). Plastic capacity of end-plate and flange cleated connections- predictions and design rules. Paper presented at the Proceedings of the 2nd International Workshop on Connections in Steel Structures: Behaviour, Strength, and Design, 10-12 April. Pittsburgh, USA.

Karlsen, F. T., & Aalberg, A. (2012). Bolted RHS end-plate joints in axial tension. Paper presented at the Proceedings of the Nordic Steel Construction Conference, 5-7 September, Oslo, Norway.

Kato, B., & Mukai, A. (1982). Bolted tension flanges joining square hollow section members (CIDECT Rep. 8B-82/3 E). University of Tokyo, Tokyo, Japan.

Kato, B., & McGuire, W. (1972). Analysis of T-stub flange connections. Journal of Structural Engineering, 99(5), 865-888.

Kulak, G. L., Fisher, J. W., & Struik, J. H. A. (2001). Guide to design criteria for bolted and riveted joint (2nd ed.). American Institute of Steel Construction.

Ministry of Construction, Housing and Utilities of the Russian Federation. (2017). SNiP II-23-81* Steel structures (SP 16.13330.2017). Retrieved from https://docs.cntd.ru/document/1200084089

Mudrov, A. (2016). Study of flange-plate connections and behaviour of bolts in tension (Master thesis). Vilnius Gediminas Technical University (in Lithuanian).

Nair, R. S., Birkemoe, P. C., & Munse, W. H. (1974). High strength bolts subject to tension and prying. Journal of the Structural Division, American Society of Civil Engineers, 100(2), 351-372.

Packer, J. A., Bruno, L., & Birkemoe, P. C. (1989). Limit analysis of bolted RHS flange plate joints. Journal of Structural Engineering, 115(9), 2226-2242. https://doi.org/10.1061/(ASCE)0733-9445(1989)115:9(2226)

Packer, J. A., & Henderson, J. E. (1997). Hollow structural section connections and trusses – A design guide (2nd ed.). Canadian Institute of Steel Construction, Toronto, Canada.

Packer, J. A., Sherman, D., & Lecce, M. (2010). Hollow structural section connections: Steel design guide No 24. American Institute of Steel Construction. Chicago, USA.

Packer, J. A., Wardenier, J., Zhao X.-L., van der Vegte, G. J., & Kurobane, Y. (2009). Design guide for rectangular hollow section (RHS) joints under predominantly static loading (2nd ed.). Geneva, Switzerland: CIDECT.

Pišković, J., Dujmović, D., & Androić, B. (2014). Probabilistic analysis of bolted RHS end-plate joints in axial tension. Paper presented at the EUROSTEEL 2014, 7th European Conference on Steel and Composite Structures. Naples, Italy: ECCS European Convention for Constructional Steelwork.

Qiu, C., Ding, C., He, X., Zhang, L., & Bai, Y. (2018). Axial performance of steel splice connection for tubular FRP column members. Composite Structures, 189, 498-509. https://doi.org/10.1016/j.compstruct.2018.01.100

Steige, Y., & Weynand, K. (2015). Design resistance of end plate splices with hollow sections. Steel Construction, 8(3), 187-193. https://doi.org/10.1002/stco.201510023

Stelco, Inc. (1981). Hollow structural sections − design manual for connections (2nd ed.). Hamilton, Ontario, Canada.

Struik, J. H. A., & de Back, J. (1969). Tests on bolted T-stubs with respect to a bolted beam-to-column connection (Stevin Laboratory Rep. 6-69-13). Delft University of Technology, Delft, The Netherlands.

Swanson, J. A. (2002). Ultimate strength prying models for bolted T-stub connections. Engineering Journal, 39(3), 136-147.

The Ministry of Environment of the Republic of Lithuania. (2005). Technical regulations of building construction. Design of steel structures. General attitudes (STR 2.05.08:2005). Vilnius, Lithuania.

Thornton, W. A. (2017). Yield Line Approaches for design of end plate tension connections for square and rectangular HSS members using end plate tensile strength. American Institute of Steel Construction, 54, 141-154.

Wang, Y. Q., Zong, L., & Shi, Y. J. (2013). Bending behaviour and design model of bolted flange-plate connection. Journal of Constructional Steel Research, 84, 1-16. https://doi.org/10.1016/j.jcsr.2013.01.012

Willibald, S., Packer, A. J., & Puthli, S. R. (2002). Experimental study of bolted HSS flange-plate connections in axial tension. Journal of Structural Engineering, 128(3), 328-336. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:3(328)

Zoetemeijer, P. (1974). A design method for the tension side of statically loaded, bolted beam-to-column connections. Stevin Laboratory, Delft University of Technology, Delft, the Netherlands.